Jeep Wrangler JK/JL/JT Front Shackle Tab Kit (Rated 10,000-lbs Tensial Strength Tow Point)
Regular price
$ 375.00
Save $ -375.00
/
Officially Rated 10,000-lbs Tensile Strength Tow Point per Table 4 SAE J684
Introducing Jeep Wrangler JK/JL/JT factory hook replacement Shackle Tab Kit, designed and manufactured by HK Offroad. JK Replaces factory hooks, JL/JT Replaces or adds to the factory open ended hook with solid 3/4" thick Shackle tabs.The shackle tab is welded to 3/8" base plate mounted to factory frame mounting location using 1/2" grade-8 hardware. The shackle tab also has 1/4" gussets on its sides for side-pull load support. Includes steel cover which replaces plastic cover on JL Rubicon Bumpers. Fits JL and JT factory Steel Rubicon bumpers. Cutting of the 16 gauge steel tube (crush can) located on the fog-light housing is required as the shackle tab kit replaces the crush can. Installation instructions available for JL/JT only. JK follows similar method.
Choose between open fog light plates or the grilled fog light plates
Kit includes two shackle tabs (one for driver side one for passenger side), Eight Grade-8 half-inch nuts and bolts, two bumper cover plates. Mounting hardware for the bumper cover plates is reused from your side wings removed from the bumper. D-RINGS NOT INCLUDED!
Build: The shackle tabs measure 3/4" thick constructed from A572 Grade-50 Steel welded to 3/8" thick steel base plate with two 1/4" gussets on each side of the shackle tab. Indestructible is an understatement.
ASTM A572 Grade 50 is considered a "workhorse" grade and is widely used in many applications. Steel mills produce channel and heavy beams with Grade 50. It is commonly used in structural applications, heavy construction equipment, building structures, heavy duty anchoring systems, truck frames, poles, liners, conveyors, boom sections, structural steel shapes, and applications that require high strength per weight ratio.
Arrives bare steel
Jeep Gladiator JT Rear Bumper Shackle Tab Kit
Regular price
$ 345.00
Save $ -345.00
/
This kit replaces the oem hooks on your JT Rear Bumper.
Construction:
3/4" Hot Rolled A572 Grade-50 steel
Factory mounting point 1-1/4" thick and tapped M14x2.0
Uses factory hardware
Arrives Bare steel - painting or coating required
Sold as a pair
For lateral pulling/recovery methods only. Do not use a high lift jack to lift the rear of the vehicle from this tab.
Jeep Wrangler JK/JL & Gladiator JT Front Recessed Winch Stubby Bumper
Regular price
$ 1,195.00
Sale price
$ 845.00
Save $ 350.00
/
Stubby Style and Recessed (Hidden) winch mount
Side Mounted Flush Mount LED light area (lights not included)
1/4" thick Winch Mounting Bottom plate
(Optional Lower Skid Plate) 3/16" thick Lower Frame Section Skid plate with 8 DOM Tubes mounts to two winch mounting points and factory mounting points on the lower side of the frame
1/4" Gussets welded to inner bumper for reinforcement
3/4" Thick Grade-50 Plate Shackle Tabs for 3/4" D-Rings and Flat Towing capabilities. Shackle tabs go through front plate reaching the frame
Bumper mounts to frame w/ eight 1/2" Grade-8 Nuts and Bolts and two factory bolts to the side of the frame
Rubicon Model Compatible
Arrives Bare Steel
Compared to 100lbs factory Rubicon Bumper with after-market winch plate and our shackle tab kit, our bumper design weighs 70 lbs so you're shaving off 30lbs of weight and keeping front end protected by solid steel.